El Paso 132 cm 54W Ceiling Fan with Light Maple

Toller Ventilator. Aufbau etwas schwierig. Wenn er aber hängt, sehr schönes Teil.

Great fan. Assembly is a bit tricky. But once it's up, it's a very nice piece.

Ventilateur posé au plafond afin d'optimiser la chaleur de notre fourneau, et il est efficace

A fan was installed on the ceiling to optimize the heat from our stove, and it is effective.

trovo i lampadari con ventilatore da soffitto utilissimi, tant'è vero che li ho in tutte le camere. Dovendone sostituire uno diventato rumoroso dopo anni di onorato servizio, ho scoperto con raccapriccio che la gran parte di quelli che vendono ora hanno il led integrato. Avendo avuto pessime esperienze in passato coi led integrati nelle lampade, visto che quando si rompono ti costringono a sostituire tutta la lampada quando prima bastava cambiare la lampadina, mi sono imbattuto in questo che ha la lampadina sostituibile. Il "corpo" del lampadario è esattamente uguale a quello che dovevo sostituire, a riprova che si tratta di un progetto datato, è stato però aggiornato grazie alle tre pale lunghe invece delle 5 pale di dimensioni medie che avevo comprato in passato. In più quello che ho preso ha le pale color rovere che fanno la loro figura. Le pale girano bene e il motore non fa rumore (per ora almeno), l'unica pecca è che alla massima velocità il lampadario si agita parecchio, a riprova del fatto che non è equilibrato (magari ho sbagliato io a montarlo). Riguardo al montaggio c'è stato un po' da penare a montare le pale, ho dovuto ruotare leggermente la ghiera interna che le sostiene (che sia stato questo a causare lo sbilanciamento?). Consiglio al riguardo di montare le pale mentre il lampadario è giù, sarebbe stato impossibile farlo da arrampicato come dicono le istruzioni. Agganciare il lampadario al soffitto al contrario è stato facilissimo, essendo la base che si ancora al soffitto esattamente uguale al precedente lampadario. Una cosa negativa che però ho riscontrato è l'assenza del dimmer, mi pareva di aver letto in qualche commento che c'era, vabbè pazienza. Il senso di rotazione della pale si può invertire tramite un interruttore posto sopra il motore. Ora l'ho messo che butta l'aria verso l' alto per l'inverno. Direi che tutto sommato sono soddisfatto, per il prezzo fanno la loro figura, ho le lampadine sostituibili che volevo e il motore non fa rumore. Unici problemi la mancanza del dimmer e le vibrazioni alla massima velocità. Ne ho subito ordinato un altro per lo studio di mia moglie (come potevo dirle di no ;)

I find ceiling fan chandeliers incredibly useful, so much so that I have them in every room. When I had to replace one that had become noisy after years of faithful service, I was horrified to discover that most of the ones on sale now have integrated LEDs. Having had bad experiences in the past with integrated LEDs in lamps, since when they break, you have to replace the entire lamp when previously you could just replace the bulb, I came across this one with a replaceable bulb. The "body" of the chandelier is exactly the same as the one I needed to replace, proving that it's an older design, but it has been updated with three long blades instead of the five medium-sized blades I had previously purchased. Plus, the one I got has oak-colored blades that look great. The blades spin well and the motor isn't noisy (at least for now). The only flaw is that at maximum speed, the chandelier shakes quite a bit, proving it's not balanced (perhaps I installed it incorrectly). Regarding assembly, it was a bit of a hassle to install the blades; I had to slightly rotate the internal ring that holds them (could this have caused the imbalance?). I recommend installing the blades while the chandelier is down; it would have been impossible to do it while climbing, as the instructions say. Hanging the chandelier upside down was very easy, as the base that anchors to the ceiling is exactly the same as the previous chandelier. One negative I did find, however, is the lack of a dimmer; I thought I'd read in some comments that it had one, but never mind. The direction of rotation of the blades can be reversed using a switch above the motor. I've now installed one that blows air upwards for the winter. Overall, I'm happy with the result; for the price, they're a good deal, I have the replaceable bulbs I wanted, and the motor isn't noisy. The only issues are the lack of a dimmer and the vibrations at maximum speed. I immediately ordered another one for my wife's studio (how could I say no ;)

Ventilateur acheté pour une 2ème fois. Très bien dans l'ensemble ,niveau bruit rien à dire ,et sa télécommande idéale plus besoin de se lever du canapé ! je recommande fortement.

I bought this fan for the second time. Overall, it's very good; the noise level is excellent, and the remote control is perfect – no need to get up from the sofa! I highly recommend it.

Matériel installé aujourd'hui.Dommage, les chevilles pour la fixation du ventilateur ne sont pas fourniesLe montage reste assez simple pour tous bons bricoleursAttention, j'ai bien dit bons bricoleurs :)Le bruit du ventilateur est très bas à vitesse moyenne, un peu plus gênant à pleine vitesse et inaudible à la petite vitesseDonc pour résumer: un très bon ventilateur avec un excellent rapport qualité/prix

Equipment installed today. It's a shame the wall plugs for mounting the fan aren't included. Assembly is fairly straightforward for any reasonably competent DIYer. (Note: I did say reasonably competent DIYers!) The fan noise is very low at medium speed, a little more noticeable at full speed, and inaudible at low speed. So, to sum up: a very good fan with excellent value for money.

(Passende Leuchtmittel LED weiter unten)Kurz und knapp: Die Montage ist für Ungeübte sicherlich etwas Fummelei, aber machbar. Vor endgültiger Festlegung der Position für den Winkel (Deckenmontage) darauf achten, dass nachher der Infrarot-Empfänger richtig ausgerichtet ist. Einhängen vom Unterteil in den Winkel und Bohrung für IR-Empfänger ausrichten > Stellung Winkel merken>dann funktioniert nachher auch alles. Empfehlung 4x 8x60 mm Markendübel 4 Spaxschrauben 6*60 mm, dann wackelt nichts und der Ventilator bleibt auch für Jahre hängen.Einhängen Ventilator in Deckenmontagewinkel:Die Reihenfolge ist für den Erfolg und zur Vermeidung von Frustration zu beachten, steht gut erklärt in der Montageanleitung. Erst Motor einhängen, Steuerung einschieben, Stromversorgungs-Stecker und Kupplungen verbinden.+ Im Betrieb ist der Empfänger recht unempfindlich auf den Empfang/ der Sender ist ausreichend stark.+ Super leise, eine dB-A Messung würde wenig Sinn machen, da nur in der höchsten Stufe etwas in dB messbar wäre (über 45 dBA), die mittlere ist als leises Flüstern so gerade hörbar. In der kleinsten Stufe ist fast nichts zu hören.+ Luftmenge: Bei uns ist der Deckenventilator über dem Fußende vom Bett montiert, die Luftbewegung ist völlig ok, auch in der kleinsten Stufe merkt man eine deutliche "Brise".+- Material/Verarbeitung: Die drei Flügel sind bis auf 0,5g identisch (gemessen: Gesamtgewicht, Teilgewicht Blattspitze, Teilgewicht Montageende), die Messung habe ich zur Vermeidung einer Unwucht vor der Montage der Flügel gemacht.+ Laufruhe: Eine ganz leichte Unruhe entsteht erst bei voller Drehzahl, aber diese ist sehr gering. Ein Wuchten der montierten Flügel wäre sehr aufwändig und ist technisch anspruchsvoll, daher habe ich 1g Unterschied im Gewicht der Flügel vernachlässigt.Eine endgültige Bewertung zum Motor / Lebensdauer kann ich erst nach ein bis zwei Jahren abgeben.+ Schaltzustand Leuchte: Viele werden den Deckenventilator an bestehender Stromleitung an der Decke betreiben. Der "230V-Lichtschalter" kann weiterhin entsprechend verwendet werden, denn der El Paso merkt sich den letzten Zustand des Leuchtmittels (ein/aus). Aus Sicherheitsgründen ist der Motor im Einschaltzustand immer ausgeschaltet.+- In der Praxis wird man das Licht zum Schlafen ausschalten und den Ventilator einschalten. Um am nächsten Abend wieder Licht beim Einschalten zun haben, muss man vorher daran denken, das Licht mit der Fernbedienung wieder einzuschalten.Da wäre eine zweite Fernbedienung schon sehr praktisch oder wünschenswert zur Platzierung neben dem "alten" 230V-Lichtschalter. Im Netz finden sich IR-Fernbedienungen aus China. Da werde ich 15,-€ zum Testen investieren :-).+ Position Leuchtmittel: Das Unterteil kann jeweils um 120° gedreht in drei Positionen verschraubt werden, damit kann abhängig vom eingesetzten Leuchtmittel eine Ausrichtung der Lichtverteilung grob erfolgen.***************************Passende Leuchtmittel**************************************Osram LED Star Classic A Lampe nicht dimmbar (diese bauform ist recht kurz und passt 100%)Die Leuchtmittel sind als Ersatz für 40-150W erhältlich, aufgelistet 75/100 W Versionen:75W Ersatz / 8W LED:https://www.amazon.de/Osram-Classic-Kolbenform-E27-Sockel-Warmwei%C3%9F/dp/B0711XQT7N/ref=sr_1_11?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&dchild=1&keywords=Osram+LED+Star+Classic+A+Lampe%2C+in+Kolbenform+mit+E27-Sockel%2C+nicht+dimmbar%2C+Ersetzt+100+Watt&qid=1594109582&sr=8-11100W Ersatz / 11W LED:https://www.amazon.de/Osram-Classic-Kolbenform-E27-Sockel-Warmwei%C3%9F/dp/B073QSXX53/ref=psdc_248429031_t1_B0711XQT7NDie 11W LED variante macht ausreichend Licht (1.420 Lumen). Der halte für das leuchtmittel kann in drei verschiedenen Positionen verschraubt werden, somit ist die Ausleuchtung im Raum anpassbar.Ich kann mit ruhigem Gewissen 5 Sterne vergeben.Was an negativen Bewertungen bei den "günstigen" anderen Deckenventilatoren zu lesen steht, hat mir vor dem Kauf deutlich zu denken geben.

(Suitable LED light sources below) In short: Assembly is a bit fiddly for beginners, but doable. Before finalizing the position of the bracket (ceiling mounting), ensure the infrared receiver is correctly aligned. Hang the base unit in the bracket and align the hole for the IR receiver > note the bracket's position > then everything will work correctly. We recommend using 4 x 8 x 60 mm brand-name wall plugs and 4 x 60 mm Spax screws; this will ensure nothing wobbles and the fan will stay in place for years. Hanging the fan in the ceiling mounting bracket: The sequence is important for success and to avoid frustration; it is clearly explained in the assembly instructions. First, attach the motor, slide in the control unit, and connect the power supply plug and connectors. + In operation, the receiver is quite insensitive to signal strength; the transmitter is sufficiently strong. + Super quiet; a dB-A measurement would be pointless, as only the highest setting would register anything in dB (over 45 dBA). The medium setting is barely audible, like a whisper. The lowest setting is almost inaudible. + Airflow: Our ceiling fan is mounted above the foot of the bed, and the airflow is perfectly adequate. Even the lowest setting provides a noticeable breeze. +- Material/Workmanship: The three blades are identical to within 0.5g (measured: total weight, partial weight of blade tip, partial weight of mounting end). I took this measurement before mounting the blades to avoid any imbalance. + Smoothness of Operation: A very slight vibration only occurs at full speed, but it is minimal. Balancing the mounted blades would be very complex and technically demanding, therefore I disregarded the 1g difference in blade weight. I can only give a final assessment of the motor/lifespan after one to two years. + Light switch status: Many will operate the ceiling fan using the existing electrical wiring in the ceiling. The "230V light switch" can still be used accordingly, as the El Paso remembers the last state of the light (on/off). For safety reasons, the motor is always switched off when the fan is on. +- In practice, you will likely switch off the light to go to sleep and turn on the fan. To have the light on again when you switch it on the next evening, you have to remember to switch the light back on with the remote control beforehand. A second remote control would be very practical or desirable for placement next to the "old" 230V light switch. IR remote controls from China can be found online. I'll invest €15 to test it :-). + Bulb position: The base can be rotated 120° and screwed into three positions, allowing for a rough adjustment of the light distribution depending on the bulb used. ***************************Suitable bulbs************************************** Osram LED Star Classic A bulb, non-dimmable (this design is quite short and fits perfectly). The bulbs are available as replacements for 40-150W bulbs; listed are 75/100W versions: 75W replacement / 8W LED: https://www.amazon.de/Osram-Classic-Kolbenform-E27-Sockel-Warmwei%C3%9F/dp/B0711XQT7N/ref=sr_1_11?__mk_de_DE=%C3%85M%C3%85%C5%BD%C3%95%C3%91&dchild=1&keywords=Osram+LED+Star+Classic+A+Lampe%2C+in+Kolbenform+mit+E27-Sockel%2C+nicht+dimmbar%2C+Ersetzt+100+Watt&qid=1594109582&sr=8-11100W Replacement / 11W LED: https://www.amazon.de/Osram-Classic-Kolbenform-E27-Sockel-Warmwei%C3%9F/dp/B073QSXX53/ref=psdc_248429031_t1_B0711XQT7ND The 11W LED version provides sufficient light (1,420 lumens). The bulb holder can be screwed into three different positions, allowing for adjustable room illumination. I can confidently give it 5 stars. The negative reviews I read for other "cheaper" ceiling fans definitely gave me pause before buying.